StockFetcher Forums · View by Author: (109 messages)  [ Display By: Date / Subject ]<< 1 ... 3 4 5 6 7 ... 11 >> 
Filter Exchange · FUN with Guppys ... a different perspective !
msg #117757
1/15/2014 12:57:07 PM

Is there a way to change the colors of the lines? I think the the change in trends would be much easier to identify if all of the short term averages were black and all the long terms were red, rather than the 5 or 6 colors that SF uses and 2 ma's use the same color line. QA little confusing on some charts

Filter Exchange · help with highs and lows
msg #117483
12/21/2013 9:20:03 PM

can someone help me with how to plot a 20 day high and 20 day low of historical volatility? I know I need "set" statements but I can't get it right.

Filter Exchange · How to determine lowest and highest values on an indicator
msg #115446
9/19/2013 6:35:21 PM


Filter Exchange · thoughts on this filter
msg #114680
7/28/2013 10:22:13 PM

I've put this filter together looking for a pullback in an uptrend. When MDVAL is bottoming out in an uptrend it indicates a winning trade. Any input regarding entries or exits will be much appreciated. Many of you have much better trading skills than I and I welcome all comments.
Fetcher[set{wrval, INDPOSITION(williams %r(10), 60) * 100 }
set{mdval, INDPOSITION(macd(12,26,1), 20) * 100 }
set{bbval, INDPOSITION(bollinger width(20), 20) * 100 }
set{mymd, mdval * 1}

close > .50
average volume(90) > 500000
mymd < .0001
ma(22) > ma(130)
do not draw mymd
draw mdval on plot bbval
draw wrval on plot rsi(2)
draw macd(22,130,1)
draw macd(12,26,9)
draw aroon oscillator(20)

sort column two ascending
chart-time is 9 months

General Discussion · What is wrong with the syntax?
msg #114206
6/23/2013 9:27:12 PM

Thx Four...your eyes are appreciated!

General Discussion · What is wrong with the syntax?
msg #114191
6/22/2013 7:13:21 PM

Can someone tell me what I am doing wrong? I keep getting errors on lines 5-9
set{RCMA1, cma(ROC(10),10)
set{RCMA2, cma(ROC(15),10)
set{RCMA3, cma(ROC(20),10)
set{RCMA4, cma(ROC(30),15)
set{KSTa, RCMA1 + RCMA2}
set{KSTb, RCMA3 + RCMA4}
set{myKST, KSTa + KSTb}
set{mySL, cma(myKST,9) }

draw myKST

General Discussion · question about drawing indicators
msg #113126
5/4/2013 1:22:15 PM

Kevin you're right about the W%R, I was trying to put the question together too quickly and didn't pay attention to the details. Here is a better example

average volume(90) > 500000
aroon oscillator(20) > 0
aroon oscillator(2) < 0
draw aroon oscillator(2) on plot aroon oscillator(20)

close is between 1 and 4.9999

General Discussion · question about drawing indicators
msg #113111
5/3/2013 2:53:27 PM

when you have two indicators as filter parameters why does SF draw them separately even if you use the draw command (see the filter example below) and is there a way around this?

close > 1
rsi(2) < 2
williams %r(2) < 2
draw rsi(2) on plot williams %R(2)

General Discussion · Are you using...
msg #112684
4/7/2013 7:21:35 PM

Thank you!!

General Discussion · Are you using...
msg #112682
4/7/2013 6:07:00 PM

I'm still holding out hope for a bar based histogram

StockFetcher Forums ·  · << 1 ... 3 4 5 6 7 ... 11 >>

*** Disclaimer *** does not endorse or suggest any of the securities which are returned in any of the searches or filters. They are provided purely for informational and research purposes. does not recommend particular securities., Vestyl Software, L.L.C. and involved content providers shall not be liable for any errors or delays in the content, or for any actions taken based on the content.

Copyright 2018 - Vestyl Software L.L.C.Terms of Service | License | Questions or comments? Contact Us
EOD Data sources: DDFPlus & CSI Data Quotes delayed during active market hours. Delay times are at least 15 mins for NASDAQ, 20 mins for NYSE and Amex. Delayed intraday data provided by DDFPlus